Black Decker Cordless Saw KS800E User Manual

3
 
f. If operating a power tool in a damp location is  
unavoidable, use a Residual Current Device (RCD)  
protected supply. Use of an RCD reduces the risk of  
electric shock.  
Intended use  
Your Black & Decker jigsaw has been designed for sawing  
wood, plastics and sheet metal. This tool is intended for  
consumer use only.  
3. Personal safety  
Safety instructions  
a. Stay alert, watch what you are doing and use  
common sense when operating a power tool. Do not  
use a power tool while you are tired or under the  
influence of drugs, alcohol or medication. A moment  
of inattention while operating power tools may result in  
serious personal injury.  
b. Use personal protective equipment. Always wear  
eye protection. Protective equipment such as dust  
mask, non-skid safety shoes, hard hat, or hearing  
protection used for appropriate conditions will reduce  
personal injuries.  
General power tool safety warnings  
Warning! Read all safety warnings and all  
!
instructions. Failure to follow all instructions may  
result in electric shock, fire and/or serious injury.  
Save all warnings and instructions for future reference.  
The term "power tool" in all of the warnings listed below  
refers to your mains operated (corded) power tool or battery  
operated (cordless) power tool.  
1. Work area safety  
c. Prevent unintentional starting. Ensure the switch is  
in the off-position before connecting to power  
source and/or battery pack, picking up or carrying  
the tool. Carrying power tools with your finger on the  
switch or energising power tools that have the switch on  
invites accidents.  
d. Remove any adjusting key or wrench before turning  
the power tool on. A wrench or a key left attached to a  
rotating part of the power tool may result in personal  
injury.  
e. Do not overreach. Keep proper footing and balance  
at all times. This enables better control of the power  
tool in unexpected situations.  
f. Dress properly. Do not wear loose clothing or  
jewellery. Keep your hair, clothing and gloves away  
from moving parts. Loose clothes, jewellery or long  
hair can be caught in moving parts.  
a. Keep work area clean and well lit. Cluttered and dark  
areas invite accidents.  
b. Do not operate power tools in explosive  
atmospheres, such as in the presence of flammable  
liquids, gases or dust. Power tools create sparks  
which may ignite the dust or fumes.  
c. Keep children and bystanders away while operating  
a power tool. Distractions can cause you to lose  
control.  
2. Electrical safety  
a. Power tool plugs must match the outlet. Never  
modify the plug in any way. Do not use any adapter  
plugs with earthed (grounded) power tools.  
Unmodified plugs and matching outlets will reduce risk  
of electric shock.  
b. Avoid body contact with earthed or grounded  
surfaces such as pipes, radiators, ranges and  
refrigerators. There is an increased risk of electric  
shock if your body is earthed or grounded.  
c. Do not expose power tools to rain or wet conditions.  
Water entering a power tool will increase the risk of  
electric shock.  
g. If devices are provided for the connection of dust  
extraction and collection facilities, ensure these are  
connected and properly used. Use of these devices  
can reduce dust related hazards  
4. Power tool use and care  
a. Do not force the power tool. Use the correct power  
tool for your application. The correct power tool will do  
the job better and safer at the rate for which it was  
designed.  
b. Do not use the power tool if the switch does not turn  
it on and off. Any power tool that cannot be controlled  
with the switch is dangerous and must be repaired.  
c. Disconnect the plug from the power source and/or  
the battery pack from the power tool before making  
any adjustments, changing accessories, or storing  
power tools. Such preventive safety measures reduce  
the risk of starting the power tool accidentally.  
d. Do not abuse the cord. Never use the cord for  
carrying, pulling or unplugging the power tool.  
Keep cord away from heat, oil, sharp edges or  
moving parts. Damaged or entangled cords increase  
the risk of electric shock.  
e. When operating a power tool outdoors, use an  
extension cord suitable for outdoor use. Use of a  
cord suitable for outdoor use reduces the risk of electric  
shock.  
4
 
d. Store idle power tools out of the reach of children  
and do not allow persons unfamiliar with the power  
tool or these instructions to operate the power tool.  
Power tools are dangerous in the hands of untrained  
users.  
e. Maintain power tools. Check for misalignment or  
binding of moving parts, breakage of parts and any  
other condition that may affect the power tools  
operation. If damaged, have the power tool repaired  
before use. Many accidents are caused by poorly  
maintained power tools.  
f. Keep cutting tools sharp and clean. Properly  
maintained cutting tools with sharp cutting edges are  
less likely to bind and are easier to control.  
g. Use the power tool, accessories and tool bits etc. in  
accordance with these instructions, taking into  
account the working conditions and the work to be  
performed. Use of the power tool for operations  
different from those intended could result in a  
hazardous situation.  
Do not touch the workpiece or the blade  
immediately after operating the tool. They can  
become very hot.  
Be aware of hidden hazards, before cutting into  
walls, floors or ceilings, check for the location of  
wiring and pipes.  
The blade will continue to move after releasing the  
switch. Always switch the tool off and wait for the saw  
blade to come to a complete standstill before putting the  
tool down.  
Warning! Contact with, or inhalation of dusts arising from  
cutting applications may endanger the health of the operator  
and possible bystanders. Wear a dust mask specifically  
designed for protection against dust and fumes and ensure  
that persons within or entering the work area are also  
protected.  
The intended use is described in this instruction manual.  
The use of any accessory or attachment or performance  
of any operation with this tool other than those  
recommended in this instruction manual may present a  
risk of personal injury and/or damage to property.  
5. Service  
a. Have your power tool serviced by a qualified repair  
person using only identical replacement parts. This  
will make sure that the safety of the power tool is  
maintained.  
Safety of others  
This appliance is not intended for use by persons  
(including children) with reduced physical, sensory or  
mental capabilities, or lack of experience and  
knowledge, unless they have been given supervision or  
instruction concerning the use of the appliance by a  
person responsible for the their safety.  
Additional power tool safety warnings  
!
Warning! Additional safety warnings for jigsaws.  
Children should be supervised to ensure that they do  
not play with the appliance.  
Hold power tool by insulated gripping surfaces,  
when performing an operation where the cutting  
accessory may contact hidden wiring or its own  
cord. Cutting accessory contacting a "live" wire may  
make exposed metal parts of the power tool "live" and  
could give the operator an electric shock.  
Vibration  
The declared vibration emission values stated in the  
technical data and the declaration of conformity have been  
measured in accordance with a standard test method  
provided by EN 60745 and may be used for comparing one  
tool with another. The declared vibration emission value may  
also be used in a preliminary assessment of exposure.  
Use clamps or another practical way to secure and  
support the workpiece to a stable platform. Holding  
the work by hand or against your body leaves it unstable  
and may lead to loss of control.  
Warning! The vibration emission value during actual use of  
the power tool can differ from the declared value depending  
on the ways in which the tool is used. The vibration level may  
increase above the level stated.  
Keep hands away from cutting area. Never reach  
underneath the work piece any reason. Do not insert  
fingers or thumb into the vicinity of the reciprocating  
blade and blade clamp. Do not stabilize the saw by  
gripping the shoe.  
When assessing vibration exposure to determine safety  
measures required by 2002/44/EC to protect persons  
regularly using power tools in employment, an estimation of  
vibration exposure should consider, the actual conditions of  
use and the way the tool is used, including taking account of  
all parts of the operating cycle such as the times when the  
tool is switched off and when it is running idle in addition to  
the trigger time.  
Keep blades sharp. Dull or damaged blades may  
cause the saw to swerve or stall under pressure. Always  
use the appropriate type of saw blade for the workpiece  
material and type of cut.  
When cutting pipe or conduit, make sure that they  
are free from water, electrical wiring, etc.  
5
 
Labels on tools  
Residual risks  
Additional residual risks may arise when using the tool which  
may not be included in the enclosed safety warnings. These  
risks can arise from misuse, prolonged use etc.  
Warning! To reduce the risk of injury, the user  
must read the instruction manual.  
Even with the application of the relevant safety regulations  
and the implementation of safety devices, certain residual  
risks cannot be avoided. These include:  
Electrical safety  
This tool is double insulated; therefore no earth  
wire is required. Always check that the power  
supply corresponds to the voltage on the rating  
plate.  
Injuries caused by touching any rotating/moving parts.  
Injuries caused when changing any parts, blades or  
accessories.  
If the supply cord is damaged, it must be replaced by the  
manufacturer or an authorised Black & Decker Service  
Centre in order to avoid a hazard.  
Injuries caused by prolonged use of a tool. When using  
any tool for prolonged periods make sure you take  
regular breaks.  
Impairment of hearing.  
Features  
1. Lock-on button  
2. Variable speed on/off switch  
3. Blade storage compartment cover  
4. Shoe plate locking lever  
5. Shoe plate  
Health hazards caused by breathing dust developed  
when using your tool (example:- working with wood,  
especially oak, beech and MDF).  
Use  
6. Blade support roller  
7. Tool-free blade clamp  
Adjusting the shoe plate for bevel cuts (fig. C and D)  
Warning! Never use the tool when the shoe plate is loose or  
removed.  
Assembly  
The shoe plate (5) can be set to a left or right bevel angle of  
up to 45°.  
Warning! Before attempting any of the following operations,  
make sure that the tool is switched off and unplugged and  
that the saw blade has stopped. Used saw blades may be  
hot.  
Pull the shoe plate locking lever (4) outwards to unlock  
the shoe plate (5) from the 0 degree position (fig. D).  
Pull the shoe plate (5) forward and set the required  
bevel 15°, 30° and 45° indicated in the bevel angle  
window.  
Fitting the saw blade (fig. A)  
Hold the saw blade (8) as shown, with the teeth facing  
forward.  
Push the shoe plate locking lever (4) back towards the  
saw to lock the shoe plate (5).  
Push and hold the blade clamp (7) down.  
Insert the shank of the saw blade into the blade holder  
(9) as far as it will go.  
To reset the shoe plate (5) for straight cuts:  
Pull the shoe plate locking lever (4) outwards to unlock  
the shoe plate (5).  
Set the shoe plate (5) to an angle of 0° and push the  
shoe plate backwards.  
Push the shoe plate locking lever (4) back towards the  
saw to lock the shoe plate (5).  
Release the blade clamp (7).  
Saw blade storage (fig. B)  
Saw blades (8) can be stored in the storage compartment  
located on the side of the tool.  
Open the cover (3) of the saw blade storage  
compartment by holding the tab on the top of the cover  
(3) and pulling it outward.  
The blades are retained in the compartment by a  
magnetic strip. To remove a blade, press down on one  
end of the blade to raise the other end, and remove.  
Close the cover (3) of the saw blade storage  
compartment and make sure that it is latched closed.  
Switching on and off  
To switch the tool on, press the variable speed on/off  
switch (2).  
To switch the tool off, release the variable speed on/off  
switch (2).  
For continuous operation, press the lock-on button (1)  
and release the on/off switch (2).  
To switch the tool off when in continuous operation,  
press the on/off switch (2) and release it.  
Warning! Close the compartment door securely before  
operating the saw.  
6
 
Sawing  
Warning! No connection is to be made to the earth terminal.  
Follow the fitting instructions supplied with good quality  
plugs. Recommended fuse: 5 A.  
Hold the tool firmly with both hands while cutting.  
The shoe plate (5) should be held firmly against the material  
being cut. This will help prevent the saw from jumping,  
reduce vibration and minimise blade breakage.  
Protecting the environment  
Let the blade run freely for a few seconds before starting  
the cut.  
Apply only a gentle pressure to the tool while performing  
the cut.  
Separate collection. This product must not be  
disposed of with normal household waste.  
Hints for optimum use  
Should you find one day that your Black & Decker product  
needs replacement, or if it is of no further use to you, do not  
dispose of it with household waste. Make this product  
available for separate collection.  
Sawing laminates  
When cutting laminates, splintering may occur which can  
damage the presentation surface. The most common saw  
blades cut on the upward stroke, therefore if the shoe plate  
is sitting on the presentation surface either use a saw blade  
that cuts on the downward stroke or:  
Separate collection of used products and packaging  
allows materials to be recycled and used again. Re-  
use of recycled materials helps prevent  
environmental pollution and reduces the demand  
for raw materials.  
Use a fine-tooth saw blade.  
Saw from the back surface of the workpiece.  
To minimise splintering, clamp a piece of scrap wood or  
hardboard to both sides of the workpiece and saw  
through this sandwich.  
Local regulations may provide for separate collection of  
electrical products from the household, at municipal waste  
sites or by the retailer when you purchase a new product.  
Black & Decker provides a facility for the collection and  
recycling of Black & Decker products once they have  
reached the end of their working life. To take advantage of  
this service please return your product to any authorised  
repair agent who will collect them on our behalf.  
Sawing metal  
Be aware that sawing metal takes much more time than  
sawing wood.  
Use a saw blade suitable for sawing metal.  
When cutting thin sheet metal, clamp a piece of scrap  
wood to the back surface of the workpiece and cut  
through this sandwich.  
You can check the location of your nearest authorised repair  
agent by contacting your local Black & Decker office at the  
address indicated in this manual. Alternatively, a list of  
authorised Black & Decker repair agents and full details of  
our after-sales service and contacts are available on the  
Internet at: www.2helpU.com.  
Spread a film of oil along the intended line of cut.  
Maintenance  
Your Black & Decker tool has been designed to operate over  
a long period of time with a minimum of maintenance.  
Continuous satisfactory operation depends upon proper tool  
care and regular cleaning.  
Regularly clean the ventilation slots in your tool using a  
soft brush or dry cloth.  
Regularly clean the motor housing using a damp cloth.  
Do not use any abrasive or solvent-based cleaner.  
Never let any liquid get inside the tool and never  
immerse any part of the tool into liquid.  
Mains plug replacement (U.K. & Ireland only)  
If a new mains plug needs to be fitted:  
Safely dispose of the old plug.  
Connect the brown lead to the live terminal in the new  
plug.  
Connect the blue lead to the neutral terminal.  
7
 
Technical data  
Guarantee  
KS800E  
TYPE 1  
Vac 230  
W 520  
min-1 0-3000  
Black & Decker is confident of the quality of its products and  
offers an outstanding guarantee. This guarantee statement  
is in addition to and in no way prejudices your statutory  
rights. The guarantee is valid within the territories of the  
Member States of the European Union and the European  
Free Trade Area.  
Voltage  
Rated input  
No-load speed  
Max. depth of cut  
Wood  
mm 70  
mm 5  
If a Black & Decker product becomes defective due to faulty  
materials, workmanship or lack of conformity, within 24  
months from the date of purchase, Black & Decker  
guarantees to replace defective parts, repair products  
subjected to fair wear and tear or replace such products to  
make sure of the minimum inconvenience to the customer  
unless:  
Steel  
Aluminium  
Weight  
mm 15  
kg 2.2  
Level of sound pressure according to EN 60745:  
Sound pressure (LpA) 89 dB(A), uncertainty (K) 3 dB(A)  
Sound power (LWA) 100 dB(A), uncertainty (K) 3 dB(A)  
The product has been used for trade, professional or  
hire purposes.  
Vibration total values (triax vector sum)  
according to EN 60745:  
The product has been subjected to misuse or neglect.  
The product has sustained damage through foreign  
objects, substances or accidents.  
Cutting wood (ah, CW) 6.0 m/s2, uncertainty (K) 1.5 m/s2  
Cutting sheet metal (ah CM ) 6.5 m/s2,  
,
Repairs have been attempted by persons other than  
authorised repair agents or Black & Decker service  
staff.  
uncertainty (K) 1.5 m/s2  
EC declaration of conformity  
To claim on the guarantee, you will need to submit proof of  
purchase to the seller or an authorised repair agent. You can  
check the location of your nearest authorised repair agent by  
contacting your local Black & Decker office at the address  
indicated in this manual. Alternatively, a list of authorised  
Black & Decker repair agents and full details of our after-  
sales service and contacts are available on the Internet at:  
MACHINERY DIRECTIVE  
KS800E  
Black & Decker declares that these products described  
under "technical data" are in compliance with:  
2006/42/EC, EN60745-1, EN60745-2-11  
Please visit our website www.blackanddecker.co.uk to  
register your new Black & Decker product and to be kept up  
to date on new products and special offers. Further  
information on the Black & Decker brand and our range of  
products is available at www.blackanddecker.co.uk.  
For more information, please contact Black & Decker at the  
following address or refer to the back of the manual.  
The undersigned is responsible for compilation of the  
technical file and makes this declaration on behalf of Black  
& Decker.  
Kevin Hewitt  
Vice-President Global Engineering  
Black & Decker Europe,  
210 Bath Road, Slough,  
Berkshire, SL1 3YD  
United Kingdom  
01-04-2010  
8
 
 
10  
 
ENGLISH  
Do not forget to register your product!  
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product  
code to Black & Decker in your country.  
 
$XVWUDOLD  
%ODFNꢀ ꢀ'HFNHUꢀꢁ$XVWUDOLDꢂꢀ3W\ꢃꢀ/WGꢃꢀ  
ꢉꢄꢀ)OHWFKHUꢀ5RDGꢌꢀ0RRURROEDUNꢌꢀꢀ  
9LFWRULDꢌꢀꢅꢋꢅꢇꢀ  
7HOꢃꢀꢄꢅꢆꢇꢈꢉꢄꢀꢊꢋꢄꢄ  
)D[ꢀꢄꢅꢆꢍꢈꢉꢈꢀꢊꢍꢎꢄꢀ  
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ  
1HZꢀ=HDODQG  
%ODFNꢀ ꢀ'HFNHUꢀ  
7HOꢃꢀꢏꢐꢎꢀꢍꢀꢉꢊꢍꢀꢋꢋꢅꢅ  
)D[ꢀꢏꢐꢎꢀꢍꢀꢉꢊꢍꢀꢋꢋꢉꢉ  
ꢊꢀ7Hꢀ$SXQJDꢀ3ODFHꢀ  
0Wꢀ:HOOLQJWRQ  
$XFNODQGꢀꢋꢄꢐꢄ  
8QLWHGꢀ.LQJGRP  
%ODFNꢀ ꢀ'HFNHUꢀ  
7HOꢃꢀꢄꢋꢈꢊꢅꢀꢊꢋꢋꢉꢅꢎ  
)D[ꢀꢄꢋꢈꢊꢅꢀꢊꢊꢋꢋꢊꢊ  
+HOSOLQHꢀꢄꢋꢈꢊꢅꢀꢊꢈꢎꢉꢈꢈ  
ꢉꢋꢄꢀ%DWKꢀ5RDGꢀ  
6ORXJKꢌꢀ%HUNVKLUHꢀ6/ꢋꢀꢅ<'ꢀ  
90561874 REV 0  
L-  
04/10  
 

Belkin Network Card F5D8055EA User Manual
Bosch Appliances Dishwasher SHU53E User Manual
Bosch Appliances Music Mixer PLE 1MA030 EU User Manual
Boss Audio Systems Music Pedal CE 3 User Manual
Boston Acoustics Speaker SoundWare Sub User Manual
Braun Electric Toothbrush 3709 User Manual
Breville Kitchen Grill BGR200 User Manual
Campbell Hausfeld Paint Sprayer IFT232 User Manual
Casio Watch 2330 User Manual
Casio Watch MA1310 EA User Manual